文档结构  
翻译进度:17%     翻译赏金:0 元 (?)    ¥ 我要打赏

Introduction

Turn a pile of trash into a toy car—and watch it go! In this activity you will learn some physics concepts and use recycled materials to build a toy car that is propelled by a balloon. You can even find a friend, build two cars and race them against each other. Whose car will go the fastest?

Background

It might not seem like it at first, but a simple balloon car is loaded with physics and engineering concepts! When you inflate a balloon, it stores potential energy in the form of stretched rubber and the compressed air inside. When you release the balloon, this energy is converted to kinetic energy—the energy of motion—as the balloon zooms around the room. Some of the energy is also converted to heat due to friction. According to the law of conservation of energy, the total amount of energy is conserved. Energy never “disappears”—it just changes to another form.

第 1 段(可获 1.99 积分)

Another way to think about the balloon's movement is to use Newton's third law of motion: For every action there is an equal and opposite reaction. When you inflate a balloon and then release the nozzle, the rubber contracts and pushes the air out the nozzle. This means that there must be an equal and opposite reaction—the air pushes back on the rubber, propelling the balloon forward. This principle is used in real rockets and jets that shoot a high-speed stream of gases out the back of their engines, propelling the vehicle forward. In this project you will use this principle to build a toy car that is propelled forward by the stream of air escaping a balloon as it deflates.

第 2 段(可获 1.55 积分)

The car also contains a simple machine: the wheel and axle. This invention has been around so long, we take it for granted—and many of us ride in wheeled vehicles every day. You will see, however, getting your wheel and axle to spin smoothly is a critical part of getting your balloon car to work!

Materials

  • Plastic bottle
  • Four plastic bottle caps
  • Wooden skewer
  • Two straws
  • Balloon
  • Tape
  • Scissors or sharp knife (Have an adult use or supervise your use of this tool.)
  • An adult helper

Preparation

  • Cut one of the straws in half.
  • Tape both pieces of the straw to one side of the water bottle.
  • Cut the wooden skewer in half and push each piece through one of the straws. These will form your axles. (Have an adult help.)
  • Have an adult help use the scissors to poke a “+”-shaped hole directly in the center of each plastic bottle cap.
  • Press each bottle cap onto the ends of the wooden skewers. These will form your wheels.
第 3 段(可获 2.11 积分)

Procedure

  • Put your car down on a flat surface and give it a good push. Make sure the car rolls easily and coasts for a bit before stopping. If your car gets stuck or does not roll smoothly make sure: your axles are parallel to each other; the hole in each bottle cap is centered; and the straws are securely taped to the water bottle and do not wobble. You can add some glue if tape is not sufficient.
  • Tape the neck of the balloon around one end of the other straw. Wrap the tape very tightly so the connection is airtight.
  • Cut a small hole in the top of the water bottle, just big enough to push the straw through.
  • Push the free end of the straw through the hole and out the mouth of the bottle.
  • Use tape to secure the straw to the bottle.
  • Blow through the straw to inflate the balloon, then put your finger over the tip of the straw to trap the air. What do you think will happen when you put the car down and release your finger?
  • Put the car down on a flat surface and release your finger. What happens?
  • See what adjustments you can make to make the car go farther.
  • What happens if you inflate the balloon more?
  • What happens if you adjust the direction the straw is aimed? Does it work best if the straw is aimed straight back?
  • Extra: There are many different ways to build a balloon car. Turn this into an engineering design project and try building your car with different materials. For example: What happens if you use a cardboard box instead of a plastic bottle for the body? What happens if you use different diameter straws? What about different materials for the wheels and axles? Get some friends and try building different cars and racing them against one another. What materials work the best?
第 4 段(可获 4.01 积分)

Observations and results

When you inflate a balloon and let it go, it zips randomly around the room. When you tape the balloon to a straw and attach it to the body of your car, however, you can control the direction of the escaping air. When the end of the straw is aimed backward, the air pushes your car forward, as described by Newton's third law of motion. Your design will be most efficient if the straw is pointed straight back and not downward or to the side. The more you inflate the balloon the more potential energy it stores, which in turn is converted to more kinetic energy, according to the law of conservation of energy—so the car will go faster.

第 5 段(可获 1.55 积分)

你可能会发现你的玩具车在第一次尝试时不能完美地工作,特别是如果它的轴不平行或轮子摆动。 太多的摩擦会导致车轮被卡住,气球没有足够的力量将车推向前方。 测试你的车子,以确保车轮自由旋转,当你推它一下,它很容易滚动。 如果没有,您可能需要对您的设计进行一些调整。 你也应该确保当把气球绑在吸管上时没有空气逸出,如果需要,可以重新把它绑的更紧一些。

第 6 段(可获 1.3 积分)

文章评论